Reviews Spalding 316 U-Turn Lift System Bracket
Ideas supply precedence to make sure the actual reliability of all Basketball system that individuals promote and also have extended warranty via formal marketers. Our specialist squad helping consumers pertaining to benefit repairs, warranty boasts, along with contacting. The particular financial transaction practice Spalding 316 U-Turn Lift System Bracket is very an easy task to carry out, choose the transportation method acting and settlement, and finish the dealing prior to your own check pick. Happy shopping.
Specification
Product Details
- Amazon Sales Rank: #9827 in Sports & Outdoors
- Size: One Size
- Brand: Spalding
- Model: 316
- Dimensions: 4.00" h x
15.00" w x
32.00" l,
63.00 pounds
Features
- Lift system bracket connects backboard to a 3.5-inch round pole, 4-inch square pole, flat wall, or roof
- Fits all Huffy Sports, Spalding, and most other residential backboards up to 54-inches large
- Offers a three-foot height adjustment range for your net
- Provides approximately 3 feet of offset from pole or wall
- System provides a firm, anchored hold at all times
- Pole not included this is only the lift system to be attached to a pole providing a mounting point for the backboard
Product Description
Connects from backboard to 4-inch square pole or flat wall
Reviews
Customer Reviews
Most helpful customer reviews
34 of 36 people found the following review helpful.
By D. Manner
I just installed this bracket on my concrete garage wall. This unit is quite heavy, and provides for infinite adjustment which was my major reason for purchase versus the alternatives. As noted in prior reviews, the installation instruction are sparse regarding wall mounting, and the correct height to mount on a wall. Here are some of my installation suggestions and hints. First, I suggest that you test assemble it loosely with all of the components that you will be using for your installation on a workbench, so that you can see everything working together before you mount it (there will be parts left over). From that test assembly, I determined the amount of travel (elevation adjustment) available in the screw jack. If you mount the the bottom of the base plate on the wall at 8' above the driveway the rim height can be adjusted from about 7' to just over 10' at the top of the screw's travel. (The instructions give a minimum elevation reference from a hole in the middle of the mount to the ground, which is an odd way to provide this measurement.) I mounted the base plate into the solid concrete beam over the garage door, with 4" lag screws into long lag screw expanding sheilds. My only complaint about the screw jack mechanism is that is seemed to be inadequately lubricated from the factory. I took mine apart (remove the hook from the bottom) and discovered that it had only a small smear of grease on the middle of the screw. I completely greased the screw, the bearing washers and the sliding surfaces of the tubes with white lithium grease. This makes the action smoother, and will hopefully prevent corrosion. Lastly, when doing the final mounting, do not tighten all of the fasteners completely in each step of assembly. Having some "play" in the joints makes getting all of the bolt holes to line up easier. I did this entire installation alone (not recommended) and offer this last tip for the most awkward part of the assembly, mounting the backboard to the elevator arms. I held the backboard upside-down and backwards to then insert the bottom bolt through the bottom elevator arms and through the bottom backboard mounting holes. The bottom arms are hanging low to the ground at this point, so you're lower on the ladder, and more stable in this position. Then using the bottom bolt as a pivot point, swing the backboard upward into its final position (with the upper arms cranked down to the lowest position to make it easier to reach) and insert the upper bolt through the upper arms and upper backboard mounting holes. I did mounted the backboard without the rim in place to make it less cumbersome and lighter. When the mount and the backboard are all loosely assembled, then go back and tighten all of the fasteners to their final tightness.
13 of 13 people found the following review helpful.
By Ryan L. Schick
I installed this on a wall. This lift system is very sturdy and allows you to adjust the backboard height to any setting between 7 and 10 feet. Most of the other adjustable systems I looked at only give you six adjustment options. Adjusting gradually works nicely for younger players. Having to use the included crank handle to lift and lower the system is nice too. The crank unhooks and can be stored out of reach of the kids. This may seem kind of trivial, but it prevents my older daughter from cranking the rim up higher than what my younger daughter can shoot. It also prevents older kids from lowering the rim to have unsupervised slam dunk contests. I mounted a 48inch Spalding backboard on this and the whole setup is rock solid. Assembly is pretty straight forward. My only complaint is that I wasn't able to locate within the instructions the exact height the unit should be off the ground. The instructions list a "minimum" height to one of the bolt holes. It would have been nice to have some sort of guidance on exactly what height was needed to hit 10 feet exactly. I ended up at 3 inches over with the unit cranked completely to the top. That was with using the minimum height measurement. I'm not moving it as there are four 1/2 inch bolts all the way through my garage wall now.
10 of 10 people found the following review helpful.
By jkalogero
This is a heavy duty mount. There are more expensive mounts. Save your money. This one is all you will need. It is easy to adjust. Be sure to have your thinking cap on and some help when you start. I would mount the backboard to the mounting bracket first ,and elevate the whole thing if you have a way to raise it. (I used the wall mount)
Search Result
The 316 U-Turn Lift System Bracket anchors your basketball backboard (back board sold separately) to a 3.5-inch round pole, a 4-inch square pole, a flat wall, or a ...
Spalding / Huffy 316 Basketball U-Turn Lift System Bracket
Spalding / Huffy 316 U-turn lift system bracket made for the 4 inch square basketball pole, connects backboard to a pole or flat wall. Replaced 315.
Amazon.com: Customer Reviews: Spalding 316 U-Turn Lift System Bracket
5 stars. "Excellent adjustment features - Review with installation notes" I just installed this bracket on my concrete garage wall. This unit is quite heavy, and ...
Spalding Basketball Backboard U-turn Lift System - Inground ...
Spalding Basketball Backboard U-turn Lift System - The Spalding 316 U-Turn Adjustable Extension Arm and Bracket give you an adjustable mounting place for virtually ...
Spalding 316 U-Turn Lift System Mounting Bracket - SportsAuthority.com
Buy Spalding 316 U-Turn Lift System Mounting Bracket - Ideal for home use, the Spalding® U-Turn Lift System mounting bracket connects from the backboard to a 4-in ...
Spalding 316 U Turn Lift System Bracket | eBay
Spalding 316 U-Turn Lift System Bracket in Sporting Goods, Team Sports, Basketball | eBay
Spalding 316 U-Turn Lift System Bracket| This Is Smart Shop Best
Spalding 316 U-Turn Lift System Bracket. Spalding 316 U-Turn Lift System Bracket Product Description. Amazon.com. The 316 U-Turn Lift System Bracket anchors your ...
Spalding 316 U-Turn Lift System Adjustable Basketball Extension ...
Spalding 316 U-Turn Lift System Adjustable Basketball Extension Arm and Bracket reviews. Find Basketball Hoop reviews at Buzzillions including 4 reviews of Spalding ...
spalding 316 u turn lift system bracket | eBay
Visit eBay for great deals on a huge selection spalding 316 u turn lift system bracket. Shop eBay!
Spalding 316 U-Turn Lift System Mounting Bracket - Product Reviews ...
Spalding 316 U-Turn Lift System Mounting Bracket Overview, Features, and Description. Ideal for home use, the Spalding& U-Turn Lift System mounting bracket connects ...
Post a Comment