Low cost Lifetime Basketball In-Ground Sleeve for Existing 3.5" Round Pole
Ideas offer antecedence to ensure the credibility coming from all Basketball system we sell and have warrantee via prescribed providers. Our own tech group providing buyers for benefit maintenance tasks, extended warranty promises, along with consulting. This exchange method Lifetime Basketball In-Ground Sleeve for Existing 3.5" Round Pole is actually quite an easy task to doh, choose the shipping procedure along with requital, and finished your deal in accordance with your current requital choice. Happy shopping.
Specification
Product Details
- Amazon Sales Rank: #7186 in Sports & Outdoors
- Size: One Size
- Brand: Lifetime
- Model: 0023
Features
- Fits all 5" x 5" Mammoth pole pad
- 3.5" Ground Sleeve - Round
- Fits 3.5" in-ground round Pole system
- Cement required for installation
- Powder Coated steel construction
Product Description
In-ground basketball system ground sleeve permits easy removal of base pole from cemented section. Simply slip the pole into the ground sleeve, and a locking tab will secure it into place. To remove pole, just removed locking tab and slide the pole out. The ground sleeve allows the rigidity of an in-ground pole while being removable for storage. Constructed in powder coated steel with dimensions 16" long x 3.5" diameter.
Reviews
Customer Reviews
Most helpful customer reviews
17 of 18 people found the following review helpful.
By Brian A. Roush
I decided to use this ground sleeve for installing my new basketball pole.The good:-Provides a less permanent installation-Allows you to rotate the pole after installation to make it square with the court-You can vary the depth/height of the pole at installationThe bad:-There are gaps in the sleeve that will allow water into it.-Will likely allow the pole and sleeve to rust together over time if not sealed-Harder to get the pole plumb during installationWhen installing, the instructions are a bit odd. It says to dig an 18" diameter hole, but only mount the front edge of the pole 4" from the court. Therefore, your pole won't be centered in the hole. I decided to make a square form out of 2x4's so that the concrete at the surface was square rather than round. This made it look better.Additionally, the instructions say to make the top of the sleeve level with the court, but then say to slope the concrete down and away from it. Obviously, this would make the concrete at the court lower than the court itself. So I made it about 1/4" higher than the court and sloped the concrete from the court edge up 1/4" to the top of the sleeve. I found that when I set the completed pole into the sleeve, it actually sat about 1/4" lower than it was supposed to, so it worked out.Following the instructions to a "t" I still ended up with the rim 1/2" too high. The good part is that when you use the sleeve, you pour concrete into the first section of the basketball pole. They give you a cap to keep the concrete in the pole, and that cap creates a rounded section of concrete that sticks out of the bottom of the pole. So, I could knock off 1/2" of that concrete and it would be a perfect 10'. Also, if your pole ends up a bit low, you could pour some sand into the sleeve to raise the pole up as needed. So in this regard, the pole sleeve allow you to fine-tune the installation if you really care that much.The bad part is that you set the sleeve in concrete using only 1 pole section of the 3. This only gives you about 3 feet to work with in trying to get the pole perfectly straight. It's not too bad, but it's not perfect. For the kids, they'll never notice.I ended up digging an 18" hole about 30" deep, and had an 18" square pad at the surface. I used about 7.5 80# bags of concrete. Plan accordingly and buy an extra bag - you don't want to be a bag short in the middle of pouring your concrete.Using the sleeve increases installation time because you have to wait for the concrete to set around the sleeve before assembling the rest of the pole and hoop. It says to wait 72 hours after pouring the concrete before you assemble it. You can do most of the backboard assembly and put concrete in the bottom pole section during this time.The last negative is that the whole point of the sleeve is to let you remove the pole. The sleeve has a small bump-out in the back of in which you install a metal tab and set-screw. This tab/screw is what keeps the pole from rotating in the sleeve. The problem is that this allows water into the sleeve, which can allow the pole and sleeve to rust together. I may end up caulking this closed.I'm happy I used the sleeve, and would still do it again.
9 of 9 people found the following review helpful.
By Eric Gridley
I decided to use the ground sleeve to make installation a bit easier. I am very glad that I did. It is time consuming, as you have to wait for the concrete to cure, but the pole is not wobbly at all. I now have the freedom of replacing the hoop down the road should I need to. I could also take out the basketball hoop temporarily if needs be. Well worth an additional $30.
6 of 6 people found the following review helpful.
By Jeff P.
Installing this sleeve was as easy, if not easier than all the other reviews have indicated. The only thing that threw me for a loop was the amount of concrete the directions said it needed - 6 90lb. bags if I remember correctly. Try fitting all that into a hole that is 18" x 24". I bought 8 80lb bags and end up returning 3 bags.The guy at Home Depot also made a good recommendation. For about $5, you can buy a multidirectional level that temporarily attaches to the pole when setting the sleeve. Because the system has to be level in many directions (think of checking your Christmas tree from many angles), this made that process extremely easy.Last, if you haven't worked with concrete before like me, be prepared for the normal stuff to have to set for several days. If you want instant gratification, consider the quick set stuff.All in all, you can do it!
Search Result
Lifetime Basketball 3.5 in Round ... Lifetime Basketball Accessories 0023 Ground Sleeve 3.5 in. Round Pole ... Lifetime 1008 3.5 Round In-Ground with a 44 in ...
Amazon.com: Lifetime Basketball In-Ground Sleeve Round Pole, 3.5 ...
In-ground basketball system ground sleeve permits easy removal of base pole from cemented section. Simply slip the pole into the ground sleeve, and a locking tab will ...
Amazon.com: Lifetime 71799 In-Ground Basketball System with 50 ...
Lifetime Basketball In-Ground Sleeve for Existing 3.5" Round Pole. $32.99. Spalding 88351 NBA 44" Polycarbonate Backboard In-Ground Basketball System. $189.00.
Ground Sleeve for 3.5 in. Round Basketball Pole (0023)
If your basketball system has a 3.5 inch round pole, Lifetimes 3.5 inch round basketball ground sleeve will provide you with the rigidity of an inground system ...
In-Ground Goals
Lifetime In-Ground Basketball System - Features a clear, ... 3.5" round pole - 3 piece (black), straight round extension arms (black), and a Slam-It® Rim ...
Basketball
In-Ground Goals; Mammoth; Wall/Roof Mount; Double Shot; ... Basketball. Since 1986, Lifetime has transformed basketball, allowing you to play the game the way you want.
Lifetime Basketball Accessories 0023 Ground Sleeve 3.5 in. Round ...
Lifetime Basketball 3.5 in Round Ground ... Lifetime Basketball Accessories 0023 Ground Sleeve 3.5 in. Round Pole ... basketball pole in ground sleeve, 3.5 round ...
Lifetime 3.5" Round Basketball Ground Sleeve - Product Reviews and ...
Lifetime Basketball Accessories 0023 Ground Sleeve 3.5 in. Round Pole. Lifetime Basketball ... Lifetime Basketball In-Ground Sleeve for Existing 3.5 Round Pole.
Lifetime Ground Sleeve for 3 5" Round in Ground Basketball System ...
Lifetime Ground Sleeve for 3.5" Round In-Ground Basketball System Pole (model 0023) If your basketball system has a 3.5 inch round pole, Lifetimes 3.5 inch round ...
Lifetime ground sleeve Basketball Equipment | Bizrate
Lifetime Basketball In-Ground Sleeve Round Pole, 3.5-Inch. In-ground basketball system ground sleeve permits easy removal of base pole from cemented section.
Post a Comment